Python termios.IGNCR Examples

def prepare_tty():                       
    "set the terminal in char mode (return each keyboard press at once) and"\
    " switch off echoing of this input; return the original settings"
    stdin_fd = sys.stdin.fileno()  # will most likely be 0  ;->
    old_stdin_config = termios.tcgetattr(stdin_fd)
    [ iflag, oflag, cflag, lflag, ispeed, ospeed, cc ] = \
        termios.tcgetattr(stdin_fd)
    cc[termios.VTIME] = 1
    cc[termios.VMIN] = 1
    iflag = iflag & ~(termios.IGNBRK |
                      termios.BRKINT |
                      termios.PARMRK |
                      termios.ISTRIP |
                      termios.INLCR |
                      termios.IGNCR |
                      #termios.ICRNL |
                      termios.IXON)
    #  oflag = oflag & ~termios.OPOST
    cflag = cflag | termios.CS8
    lflag = lflag & ~(termios.ECHO |
                      termios.ECHONL |
                      termios.ICANON |
                      # termios.ISIG |
                      termios.IEXTEN)
    termios.tcsetattr(stdin_fd, termios.TCSANOW,
                      [ iflag, oflag, cflag, lflag, ispeed, ospeed, cc ])
    return (stdin_fd, old_stdin_config) 

def _patch_iflag(cls, attrs):
        return attrs & ~(
            # Disable XON/XOFF flow control on output and input.
            # (Don't capture Ctrl-S and Ctrl-Q.)
            # Like executing: "stty -ixon."
            termios.IXON
            | termios.IXOFF
            |
            # Don't translate carriage return into newline on input.
            termios.ICRNL
            | termios.INLCR
            | termios.IGNCR
        ) 

def _patch_iflag(cls, attrs):
        return attrs & ~(
            # Disable XON/XOFF flow control on output and input.
            # (Don't capture Ctrl-S and Ctrl-Q.)
            # Like executing: "stty -ixon."
            termios.IXON | termios.IXOFF |

            # Don't translate carriage return into newline on input.
            termios.ICRNL | termios.INLCR | termios.IGNCR
        ) 

def __init__(self, printer, prot, iomanager):
    self.printer = printer
    self.prot = prot
    self.iomanager = iomanager

    (master_fd, slave_fd) = os.openpty()
    slave = os.ttyname(slave_fd)

    master_flags = fcntl.fcntl(master_fd, fcntl.F_GETFL, 0)
    fcntl.fcntl(master_fd, fcntl.F_SETFL, master_flags | os.O_NONBLOCK)

    # switch to "raw" mode - these constants come from the manpage for termios under cfmakeraw()
    master_attr = termios.tcgetattr(master_fd)
    master_attr[0] &= ~(termios.IGNBRK | termios.BRKINT | termios.PARMRK | termios.ISTRIP
                        | termios.INLCR | termios.IGNCR | termios.ICRNL | termios.IXON)
    master_attr[1] &= ~termios.OPOST
    master_attr[2] &= ~(termios.CSIZE | termios.PARENB)
    master_attr[3] &= ~(termios.ECHO | termios.ECHONL | termios.ICANON | termios.ISIG
                        | termios.IEXTEN)
    master_attr[3] |= termios.CS8
    termios.tcsetattr(master_fd, termios.TCSADRAIN, master_attr)

    # Fun detail: master will always show as /dev/ptmx, but the kernel knows from
    # the fd which PTY we're using. This means we have to use master_fd instead
    # of opening master by name.

    logging.info("Opened PTY for {} and got {}".format(prot, os.ttyname(slave_fd)))

    self.pipe_link = "/dev/" + prot + "_1"

    try:
      os.unlink(self.pipe_link)
    except OSError as e:
      # file not found is fine to ignore - anythine else and we should log it
      if e.errno != errno.ENOENT:
        logging.error("Failed to unlink '{}': {}".format(self.pipe_link, e.strerror))

    logging.info("linking {}".format(self.pipe_link))
    os.symlink(slave, self.pipe_link)
    os.chmod(self.pipe_link, 0o666)

    logging.info("{} Pipe open. Use '{}' to communicate with it".format(self.prot, self.pipe_link))

    self.rd = os.fdopen(master_fd, "r")
    self.wr = os.fdopen(master_fd, "w")

    self.send_response = True
    self.iomanager.add_file(self.rd, self.get_message) 

def read_single_keypress():
    """Waits for a single keypress on stdin.
    https://stackoverflow.com/a/6599441/1497443

    This is a silly function to call if you need to do it a lot because it has
    to store stdin's current setup, setup stdin for reading single keystrokes
    then read the single keystroke then revert stdin back after reading the
    keystroke.

    Returns the character of the key that was pressed (zero on
    KeyboardInterrupt which can happen when a signal gets handled)

    """
    if fcntl is None or termios is None:
        raise ValueError('termios and/or fcntl packages are not available in your system. This is possible because you are not on a Linux Distro.')
    fd = sys.stdin.fileno()
    # save old state
    flags_save = fcntl.fcntl(fd, fcntl.F_GETFL)
    attrs_save = termios.tcgetattr(fd)
    # make raw - the way to do this comes from the termios(3) man page.
    attrs = list(attrs_save)  # copy the stored version to update
    # iflag
    attrs[0] &= ~(termios.IGNBRK | termios.BRKINT | termios.PARMRK |
                  termios.ISTRIP | termios.INLCR | termios.IGNCR |
                  termios.ICRNL | termios.IXON)
    # oflag
    attrs[1] &= ~termios.OPOST
    # cflag
    attrs[2] &= ~(termios.CSIZE | termios. PARENB)
    attrs[2] |= termios.CS8
    # lflag
    attrs[3] &= ~(termios.ECHONL | termios.ECHO | termios.ICANON |
                  termios.ISIG | termios.IEXTEN)
    termios.tcsetattr(fd, termios.TCSANOW, attrs)
    # turn off non-blocking
    fcntl.fcntl(fd, fcntl.F_SETFL, flags_save & ~os.O_NONBLOCK)
    # read a single keystroke
    try:
        ret = sys.stdin.read(1)  # returns a single character
    except KeyboardInterrupt:
        ret = 0
    finally:
        # restore old state
        termios.tcsetattr(fd, termios.TCSAFLUSH, attrs_save)
        fcntl.fcntl(fd, fcntl.F_SETFL, flags_save)
    return ret 

def feed(self, data):
        """
        Feed the input stream.

        :param data: Input string (unicode).
        """
        assert isinstance(data, six.text_type)

        if _DEBUG_RENDERER_INPUT:
            self.LOG.write(repr(data).encode('utf-8') + b'\n')
            self.LOG.flush()

        # Handle bracketed paste. (We bypass the parser that matches all other
        # key presses and keep reading input until we see the end mark.)
        # This is much faster then parsing character by character.
        if self._in_bracketed_paste:
            self._paste_buffer += data
            end_mark = '\x1b[201~'

            if end_mark in self._paste_buffer:
                end_index = self._paste_buffer.index(end_mark)

                # Feed content to key bindings.
                paste_content = self._paste_buffer[:end_index]
                self.feed_key_callback(KeyPress(Keys.BracketedPaste, paste_content))

                # Quit bracketed paste mode and handle remaining input.
                self._in_bracketed_paste = False
                remaining = self._paste_buffer[end_index + len(end_mark):]
                self._paste_buffer = ''

                self.feed(remaining)

        # Handle normal input character by character.
        else:
            for i, c in enumerate(data):
                if self._in_bracketed_paste:
                    # Quit loop and process from this position when the parser
                    # entered bracketed paste.
                    self.feed(data[i:])
                    break
                else:
                    # Replace \r by \n. (Some clients send \r instead of \n
                    # when enter is pressed. E.g. telnet and some other
                    # terminals.)

                    # XXX: We should remove this in a future version. It *is*
                    #      now possible to recognise the difference.
                    #      (We remove ICRNL/INLCR/IGNCR below.)
                    #      However, this breaks IPython and maybe other applications,
                    #      because they bind ControlJ (\n) for handling the Enter key.

                    #      When this is removed, replace Enter=ControlJ by
                    #      Enter=ControlM in keys.py.
                    if c == '\r':
                        c = '\n'
                    self._input_parser.send(c)